doc:hw_bootloader
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | |||
doc:hw_bootloader [2014/08/08 21:21] – wsauer | doc:hw_bootloader [2014/08/10 12:25] (current) – wsauer | ||
---|---|---|---|
Line 123: | Line 123: | ||
- | Das All-in-One Package (Flashloader_Package.zip) | + | You can find the All-in-One Package (Flashloader_Package.zip) |
- | In diesem Paket sind neben dem aktuellen Flashloader- und Firmwarefile das eigentliche Flashtool | + | Contained in the package you will find the actual flashloader- and firmwarefile the flashtool |
- | Die drei Batchdateien sind an den jeweiligen Anwendungsfällen | + | Three batchfiles are in regards of the purpose as "flash flashloader |
- | Für den initialen Flashvorgang nach Hardwarebestückung und/oder Kauf eines DXM-BT | + | For the initial flashprocess after hardware assembly and / or buying of an DXM-BT |
- | Hinweis: \\ Bei der obigen Hardwarebeschreibung für ein mögliches | + | Note: In regards of the hardwaredescription for a possible |
- | ===== Flashen von Flashloader und Firmware mit dem Batchaufruf | + | ===== Flashing of flashloader and firmware with calling the batchfile |
- | Nachdem im ersten Schritt das All-in-One Package besorgt und abgelegt wurde, wird im nächsten Schritt der Flashvorgang durch Aufruf von… | + | After as an first you got the all-in-one package and this has been saved,the next step is to call the … |
Line 147: | Line 147: | ||
- | …gestartet. Wobei x hier als Platzhalter für den jeweiligen | + | batch. x is standing for the number of the COM-port of the USB-UART |
- | Hinweis: | + | Note: |
- | Bevor der Flashvorgang gestartet werden kann ist sicherzustellen, | + | Before the flashprocess can be started you have to assure that the USB-UART |
Line 159: | Line 159: | ||
- | ===== Auslesen der Hardwarekennung | + | ===== Readout of the hardwarerecognition |
- | Nachdem die stm32flash_all.bat | + | After processing the stm32flash_all.bat |
- | **Wichtig:** | + | **Important:** |
- | Die ersten Zeilen des Bildes zeigen einen Flash-Versuch, wenn die Verbindung zwischen | + | The first rows of the output show the result on an not succesfull flash attempt, were the connection between the USB-UART |
- | Nach dem ersten Drittel des Bildschirmes wird mit erneutem Aufruf von stm32flash_all.bat COM5 dargestellt, | + | After the first third of the output you can see the information given out in regards of an succesfull |
Line 177: | Line 177: | ||
- | ===== Flashen des Flashloader/Bootloader | + | ===== Flashing of the flashloader/bootloader |
- | Nach Bestätigung der Eingabeaufforderung mit einer beliebigen Taste wird der Flashvorgang mit dem Flashloader gestartet. | + | After pressing any key the flashprocess will be started. |
Line 189: | Line 189: | ||
- | ===== Flashen der Firmware | + | ===== Flashing of the firmware |
- | Nachdem der Flashvorgang mit dem Flashloader | + | After successful completion of the flashprocess with the flashloader |
Line 204: | Line 204: | ||
- | ===== Ende des Flashvorgangs | + | ===== End of the flashprocess |
- | Nachdem der Flashvorgang der Firmware erfolgreich abgeschlossen wurde (100% Done) wird die Firmware automatisch gestartet | + | After the sucessfull flashing of the firmware |
- | ===== Flashen der Firmware mit dem integrierten Bootloader | + | ===== Flashing of the firmware with integrated bootloader |
Line 216: | Line 216: | ||
- | ====== | + | ====== |
- | Dieser Schritt wird nur für die Vollständigkeit und zur Darstellung der UART-Schnittstellengeschwindigkeits-Umstellung des BTM182/ | + | This step is only for completeness to the change of UART-Interfacespeed of the |
- | Zum Programmieren des BT- Chips muß der USB-Seriell | + | To program the BT- chip you need to connect the USB-serial |
- | Im Auslieferzustand ist der BTM182/ | + | In delivery status the BTM182/ |
doc/hw_bootloader.txt · Last modified: 2014/08/10 12:25 by wsauer